Home
About Herd
Products
Contact Us
FAQs
You are here:
Herd_Seeder_Products
:
750_seeder_parts
Shopping cart is empty.
To order, please choose your part below:
1 - 750-1091 Warning Spinning Blades decal
2 - 750-102 750-102 Blades for fan, with bolts - 420
3 - 750-106 Seed Gate Guides
4 - 750-107 one quarter inch x one half inch Cap screws to hold control plate to base plate
5 - 750-111 Five sixteenths X two inch Spring pin, for driven end of power take-off shaft and fan
6 - 750-46 Bearing shield kit, nylon bearing, snap ring and thrust washer for G and G
6 - 750-47 Bearing Retainer for G and G
6 - 750-79P Nylon bearing for plastic shield of Weasler power take-off shaft
6 - 750-80P Bearing retainer for plastic shield of Weasler power take-off shaft
6 - 750-843 Cross and Bearing Kit for G and G
7 - 750-116 Tension spring
8 - 750-117 Eye bolt
9 - 750-407 Five sixteenths x one inch bolt with nut and lockwasher
10 - 750-213 Bracket for control handle, upper and lower
12 - 750-144 Hopper base plate
13 - 750-145 Fan base only - to which blades fasten
14 - 750-146 Seed opening gauge with bolt - complete
14 - 750-146B Bottom part only of 146 seed gauge
14 - 750-146U Upper part only of 146 seed gauge
15 - 750-147 Regular agitator with bolt and nut
16 - 750-148 Fan, complete with spring pin
17 - 750-149 Opening control plate, with linkage
18 - 750-150P Twenty five and one quarter inch shielded power take-off shaft for one and three eighths power take-off with one inch driven end
19 - 750-150FP Broadcaster end of twenty five and one quarter inch power take-off shaft
20 - 750-150MP Tractor end of twenty five and one quarter inch power take-off shaft
21 - 750-2000 Gear box, complete for 540 rpm
21 - 750-2000M Gear box, complete for 1,000 rpm
22 - 750-152 Washer - one inch bore - used on fan shaft in hopper
23 - 750-153 Z angles used to carry gear box - Right side - not shown in drawing
23 - 750-154 Z angles used to carry gear box - Left side
24 - 750-212 Handle assembly for 750
25 - 750-211 Hopper for Model 750 eleven and one half Cu Ft capacity
26 - 750-158 Lime agitator with bolt used for dolomite or dehyd lime
27 - 750-159 L Base clamp lower
28 - 750-160 L Base Clamp - upper - welded to hopper
29 - 750-418 one half inch x 3 inch Machine bolt with nuts and flat washers
30 - 750-419 three eighths x one inch Machine bolt with lock washers
31 - 750-407A Five sixteenths x one inch Machine bolt with nut and washer
32 - 750-420 Five sixteenths x three quarters inch Carriage bolt with nut and lock washer
33 - 750-421 Five sixteenths x one inch Carriage bolt with nut
34 - 750-422 Five sixteenths x one three quarters inch bolt with nut - used in agitator 147
35 - 750-1093 Deflector - 22 inches long - not shown in drawing
36 - 750-92P Plastic Shield for tractor half of Weasler power take-off shaft - includes 79P and 80P
36 - 750-95 Plastic shield for tractor half of G and G power take-off shaft - includes 46 and 47
37 - 750-93P Plastic shield for seeder half of Weasler power take-off shaft - includes 79P and 80P
37 - 750-94 Plastic shield for seeder half of G and G power take-off shaft - includes 46 and 47
38 - 750-215 Fertilizer instruction decal for Model 750
39 - 750-216 Model number decal for Model 750
40 - 750-989C Seeding chart decal
41 - 750-222 Assembly C complete, of base plate 144 and parts
42 - 750-223 Hopper base ring
43 - 750-86A five sixteenths x one inch Capscrew with two nuts and flat washer
44 - 750-1123 Stainless steel compression spring used between agitator and washer
45 - 750-1126 One quarter inch x three eighths hexhead capscrew
46 - 750-101 Yoke only - for tractor end of G and G power take-off shaft
46 - 750-96 Yoke only for tractor half of Weasler power take-off shaft
47 - 750-103 Yoke Only Broadcaster Half of G and G power take-off shaft
47 - 750-97 Yoke only for broadcaster half of Weasler power take-off shaft
750-206 Herd Sure Feed Broadcaster decal
750 Seeder
